|
340 Exhaust Manifold Heat Shield
This heat shield fits all 1968-70, 340 engines with the HP style driver's side exhaust manifold, and it protects the spark plug wire boot from contacting the manifold.
|
|
340 Four-Barrel Nameplate Emblem
340 Four-Barrel Nameplate Emblem Hood
|
|
400 Magnum Emblem
400 Magnum Nameplate Emblem - Hood
|
|
440 Magnum Emblem
|
|
Air Cleaner Wing Nut
Judges notice everything, right down to the wing nut on your air cleaner
|
|
Battery Hold Down Strap
|
|
Black Wrinkle Cast Aluminum Valve Cover Set
Dress up your 426 Hemi with this handsome Black Wrinkle Cast Aluminum Hemi Valve Cover Set
|
|
Camshaft
Developed, dyno'd and track tested by engineers, these cams are developed for increased power and rpm potential while maintaining reliability and the best possible low-speed characteristics
|
|
Camshaft Bearings
Complete engine set of Camshaft Bearings
|
|
Camshaft Sprocket Bolt Kit
Sprocket Bolt Kit for 3-Bolt Mounting
|
|
Cast Iron Cylinder Head Steel Shim Gaskets
0.020" Compression Thickness
|
|
Charger Emblem - Mounts With Prongs
|
|
Charger Emblem - Mounts With Two Sided Tape
Held on With Two Sided Tape
|
|
Chrome Distributor Hold-Down Clamp
Under the hood, every detail matters, and chrome is the perfect enhancement
|
|
Composition Material Cylinder Head Gaskets
Gaskets can be used for replacement or competition applications up to 12.5:1 compression ratio
|
|
Control Unit Wiring Harness Kit
For Electronic Ignitions
|
|
Crank Bolt Package
These Crank Bolt Packages are used to attach the Damper to the Crankshaft
|
|
Crank Key Package
This Crank Key Package locates crank sprocket on the nose of the crank
|
|
Cuda 383 Nameplate
Hood (1970-71 'Cuda with Shaker or Sport Hood)
|
|
Cylinder Head Hardware Kit
Cylinder Head Hardware Kit contains 4 head freeze plugs and 10 dowel pins for the rocker shaft stands
|
|
Damper Degree Timing Tape
Marked in 90 degree increments
|
|
Dart Nameplate
Dart Nameplate Emblem (1970-75 Dart)
|
|
Deep Oil Pan
Improves the cooling and lubrication of critical transmission components
|
|
Dodge Challenger/Plymouth Barracuda Rocker Sill Plate
Unless your classic has been hermetically sealed since it was new, your rockersill plates are probably heavily scratched and/or damaged
|
|
Double Roller Chain and Sprocket Sets
These high-strength sets provide added durability and decreased rotational friction versus the production silent chains
|
|
Engine Teardown Gasket Set
Engine Teardown Gasket Set includes all gaskets needed for complete Hemi engine teardown
|
|
Fan Shroud
Restoration Radiator Cooling Fan Shroud
|
|
Forged Aluminum Piston
Features valve notches and floating pin
|
|
Forged Crankshaft
High-strength, high-quality Forged Crankshafts machined from 4340 steel
|
|
Freeze Plugs
These round, press-in engine block Freeze Plugs fit standard or Mopar Performance race cast iron blocks
|
|
Hood Pin and Cable Kit
Kit includes a pair of hood pins and all attachment hardware
|
|
Hydraulic Tappet
Hydraulic Tappet
|
|
Intermediate Shaft Bushing
|
|
Magnum Nameplate
Hood (1972-74 Charger Rallye with Power Bulge Hood)
|
|
Max Wedge Intake Hardware Kit
Hardware kit required for Max Wedge Intake Manifold Installation
|
|
Max Wedge Intake Linkage Package
Linkage kit required for Max Wedge Intake Installation
|
|
Mechanical Tappet
0.005" Undersize
|
|
Muscle Car Voltage Regulator
For restoration or repair, Mopar Performance offers this factory reissue of the Voltage Regulator used on muscle cars of the early 1970s
|
|
Offset Camshaft Bushing Set
Offset Camshaft Bushing Set includes 5 bushings; 2, 4, 6, 8 offset, plus 1 on-center bushing
|
|
Oil Slinger
Protects front seal from excessive oil contact
|
|
Original Replacement Distributor Cap
Replacement for the original tan-colored distributor cap used in Chrysler high-performance V8 muscle cars of the late 1960s and early 1970s
|
|
R/T Emblem
1969 Charger R/T
|
|
Radiator Cap
When you open the hood, it's right there where everyone can see it, especially the judges. If your radiator cap is more than ten years old or just looks bad, replace it with this original equipment quality piece
|
|
Replacement Valve Cover Gaskets
Rubber Reinforced Cork Replacement Gasket for Mopar Performance Valve Covers
|
|
Restoration Battery Tray
Manufactured to exact specifications, this tray comes e-coated to protect it from chemical and moisture exposure
|
|
Road Runner Decal
Mopar offers replacement Road Runner Decasl for the your Mopar. If your decals are damaged or badly faded, replace them with these brand new pieces. Beep-Beep!
|
|
Rocker Sill Plate
Unless your classic has been hermetically sealed since it was new, your rocker sill plates are probably heavily scratched and/or damaged
|
|
Roller Tappet Set
Roller Tappet Set includes matched pair with guide bar
|
|
Shifter Boot
If your shifter boot is damaged, worn or missing, we've got you covered
|
|
Six Pack Hood Decal
Proudly proclaim to the world what you've got under the hood
|
|
Steel Vibration Damper
Features a steel ring and a universal 6-bolt front pulley mount pattern
|
|
Super Bee Nameplate
Hood (1970 Super Bee with Power Bulge Hood)
|
|
Super Gold ECU
Unit can handle the high current demand of the high-performance coil (P3690560), while keeping dwell variation to less than 1 from 1000 to 10,000 rpm.
|
|
Timing Cover Chrome Bolt Package
Engine chrome dress-up projects are incomplete without chrome bolts
|
|
Valve Guides
Silicon-bronze alloy Valve Guides are designed modify, rebuild or repair aluminum heads
|
|
Valve Seals
Made of high-temp Viton material, these Valve Seals feature a full or semi-umbrella shape for best dual-purpose use
|
|
Valve Stem Lash Caps
5/16 Inch Stem
|
|
Window Regulator Repair Gear
Genuine Mopar Window Regulator Repair Gear
|
